Certified Copyright 2017 Control4 Corporation. All rights reserved. Control4 JVC KENWOOD JVC KENWOOD DLA-RS640_RS540_X990R_X790R_20LTD DLA-RS640_RS540_X990R_X790R_20LTD 8/11/2017 4:00 PM 9/21/2017 9:30 AM 101 devices_sm\c4.gif devices_lg\c4.gif lua_gen ip DriverWorks projector True False 2 0 0 0 1 6 Serial 232 1 True False False True RS_232 1000 1 HDMI 1 5 True False False False HDMI 1001 1 HDMI 2 5 True False False False HDMI 5001 6 PROJECTOR 2 False False False False TV 6000 1 Network 4 False False False False TCP 20554 True True True 7000 1 Room Selection - Output 7 False False False False VIDEO_SELECTION DiscreteCodes 0 0 False 19200 8 none 1 none 232 Control4 certified on 10/4/2017 for software released version: 2.10.0 JVC Projector Network and Serial Driver HARDWARE SETUP ============== Serial Control By Default the Projector should come with the control method set to serial. Menu/Functions/Communication Terminal Use a DB9 Cross (null modem) cable to connect to the controller. Baud rate : 19200bps Data length : 8 bits Parity : No Stop bit : 1 bit Flow control : No Connector : D-Sub 9pin Projector input : Control(RS-232C) Network Control The projector will come set to a static address. Set to DHCP or set this to a static address appropriate for your network. Turn on Control4 mode under network settings. Driver Notes and Limitations =========================== ISF MODE: You must turn the ISF Mode to ON before you can select the day or night modes. If the ISF is turned off and you have programming to change it to night mode the projector will ignore the command. Power On Delay Seconds: Used to establish the amount of time that will elapse during the power-on sequence before the driver continues to issue commands. Power Off Delay Seconds: Used to establish the amount of time that will elapse during the power-off and cool down sequence before the driver continues to issue commands. Power Off and Query Delay Seconds: Projectors have multiple power states like warm up and cool down. This timer is used to query the power status after the projector has booted up and cooled down. Then will allow the driver to send commands after it is fully on or fully off. PROGRAMMING =========== Variable: Projector_Operating_Status There are 4 states to this variable ON OFF COOLING EMERGENCY To access this variable go to programming and expand the device variables for the projector. Select the Projector_Operating_Status in the device events window (left). Do the same on the device action (right). In the Device Actions go to the conditionals of the Projector_Operating_Status variable. This is where you can type in the status of the variable. Example, you might want to trigger an email when the projector goes into its EMERGENCY state. Your script might say: When the variable (Room Name) ->Projector_Operating_Status changes If (Room Name) ->Projector->Projector_Operating_Status EQUALTO EMERGENCY Email Notification to 'dealer@bestdealer.com' with subject as : EMERGENCY Device Specific Commands: -- _4Keshift -- Anamorphic -- Aspect -- Back Color -- Clear Black -- Clear Motion Drive -- Color Management -- Color Profile -- Color Temp -- Color Temp Correction -- Color Space -- Colorimetry -- Deep Color -- Dynamic Control -- Eco Mode -- Gamma Table -- Gamma Correction -- Graphic Mode -- HDMI Input Level -- HDMI Color Space -- HDMI 2D 3D -- HDMI Phase Adjustment -- HDR -- High Altitude -- Intelligent Lens Aperture -- Installation Style -- Lamp Power -- Lens Memory -- Low Latency -- Mask -- Menu Position -- Motion Enhance -- Off Timer -- Picture Mode -- Source -- Source Display -- Trigger Please note that not all commands are supported in each model. Check the user manual for your specific model. Version 101: -- Initial Release Display Globals DisplayGlobals _4Keshift Set _4K e-shift to PARAM1 NAME Mode LIST False Off On Anamorphic Set Anamorphic Mode to PARAM1 NAME Mode LIST False Off A B Aspect Set Aspect Ratio PARAM1 NAME Mode LIST False Zoom Auto Just Back Color Set Back Color to PARAM1 NAME Mode LIST False Blue Black Clear Black Set Clear Black to PARAM1 NAME Mode LIST False Off Low High Clear Motion Drive Set Clear Motion Drive to PARAM1 NAME Mode LIST False Off Low High Inverse Telecine Color Management Set Color Management to PARAM1 NAME Mode LIST False Off On Color Profile Set Color Profile to PARAM1 NAME Mode LIST False Off Film1 Film2 Film3 Standard Cinema Cinema2 Anime Anime2 Video x.v.Color HDR BT.2020 THX Custom1 Custom2 Custom3 Custom4 Custom5 3D Cinema 3D Video 3D Animation 3D Film 3D THX DCI Color Temp Set Color Temp to PARAM1 NAME Mode LIST False 5500K 6500K 7500K 9300K High Bright Custom1 Custom2 HDR Xenon1 Xenon2 Xenon3 Color Temp Correction Set Color Temp Correction to PARAM1 NAME Mode LIST False 5500K 6500K 7500K 9300K High Bright Xenon1 Xenon2 Xenon3 Color Space Set Color Space to PARAM1 NAME Mode LIST False RGB YUV x.v.Color Colorimetry Set Colorimetry to PARAM1 NAME Mode LIST False No Data BT.601 BT.709 xvYCC601 xvYCC709 sYCC601 Adobe YCC601 Adobe RGB BT.2020 Constant Luminance BT.2020 Non-Constant Luminance Reserved (Other) Deep Color Set Deep Color to PARAM1 NAME Mode LIST False 8 bit 10 bit 12 bit Dynamic Control Set Dynamic Control to PARAM1 NAME Mode LIST False Off Mode1 Mode2 Eco Mode Set Eco Mode to PARAM1 NAME Mode LIST False Off On Gamma Table Set Gamma Table to PARAM1 NAME Mode LIST False Normal A B C Custom1 Custom2 Custom3 Film1 Film2 Hybrid Log ST.2084 Gamma Correction Set Gamma Correction to PARAM1 NAME Mode LIST False 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 Normal A B C Film1 Film2 Hybrid Log Import ST.2084 Graphic Mode Set Graphic Mode to PARAM1 NAME Mode LIST False 2K 4K HDMI Input Level Set HDMI Input Level to PARAM1 NAME Mode LIST False Standard(16-235) Enhanced(0-255) Super White(16-255) Auto HDMI Color Space Set HDMI Color Space to PARAM1 NAME Mode LIST False Auto YCbCr(4:4:4) YCbCr(4:2:2) RGB HDMI 2D 3D Set HDMI 2D/3D to PARAM1 NAME Mode LIST False 2D Auto Side by Side Top and Bottom HDMI Phase Adjustment Set HDMI Phase Adjustment to PARAM1 NAME Mode LIST False Standard Flip(L/R Switch) HDR Set HDR to PARAM1 NAME Mode LIST False SDR HDR SMPTE ST 2084 None High Altitude Set High Altitude to PARAM1 NAME Mode LIST False Off On Intelligent Lens Aperture Set Intelligent Lens Aperture to PARAM1 NAME Mode LIST False Off Auto1 Auto2 Installation Style Select Installation Style to PARAM1 NAME Mode LIST False Front Ceiling Mount (F) Rear Ceiling Mount (R) Lamp Power Set Lamp Power to PARAM1 NAME Mode LIST False Normal High Lens Memory Select Lens Memory to PARAM1 NAME Mode LIST False Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 Mode 7 Mode 8 Mode 9 Mode 10 Low Latency Set Low Latency to PARAM1 NAME Mode LIST False Off On Mask Set Mask to PARAM1 NAME Mode LIST False Off On Menu Position Set Menu Position to PARAM1 NAME Mode LIST False Left-Top Right-Top Center Left-Bottom Right-Bottom Left Right Motion Enhance Set Motion Enhance to PARAM1 NAME Mode LIST False Off Low High Off Timer Set Off Timer to PARAM1 NAME Mode LIST False Off 1 Hour 2 Hours 3 Hours 4 Hours Picture Mode Set Picture Mode to PARAM1 NAME Mode LIST False Film Cinema Animation Natural HDR THX isf-Day isf-Night THX-Bright THX-Dark User1 User2 User3 User4 User5 Source Set Source Mode to PARAM1 NAME Mode LIST False 480p 576p 720p50 720p60 1080i50 1080i60 1080p24 1080p50 1080p60 No Signal 720p 3D 1080i 3D 1080p 3D 4K(4096)60 4K(4096)50 4K(4096)30 4K(4096)25 4K(4096)24 4K(3840)60 4K(3840)50 4K(3840)30 4K(3840)25 4K(3840)24 1080p25 1080p30 2048x1080 p24 2048x1080 p25 2048x1080 p30 2048x1080 p50 2048x1080 p60 3840x2160 p120 4096x2160 p120 Source Display Set Source Display to PARAM1 NAME Mode LIST False Off On Trigger Set Trigger Mode to PARAM1 NAME Mode LIST False Off Power Anamorphic Log Level LIST false 2 - Warning 0 - Alert 1 - Error 2 - Warning 3 - Info 4 - Debug 5 - Trace Log Mode LIST false Off Off Print Log Print and Log Command Delay Milliseconds RANGED_INTEGER false 250 200 2500 Power On Delay Seconds RANGED_INTEGER false 10 1 120 Power Off Delay Seconds RANGED_INTEGER 1 120 8 Power Status Query Delay Seconds RANGED_INTEGER 1 30 3 NetworkKeepAliveIntervalSeconds RANGED_INTEGER false 30 15 120 Connected To Network STRING true false JVCKENWOOD:Projector Control4 certified on 10/4/2017 for software released version: 2.10.0