Certified Copyright 2016 Control4 Corporation. All rights reserved. Control4 JVC KENWOOD JVC KENWOOD DLA-X5500_RS420 (SERIAL) (IP) DLA-X5500_RS420 10/01/2015 3:00 PM 1/3/2017 3:30 PM 101 devices_sm\c4.gif devices_lg\c4.gif lua_gen ip DriverWorks projector True False 2 0 0 0 1 6 Serial 232 1 True False False True RS_232 1000 1 HDMI 1 5 True False False False HDMI 1001 1 HDMI 2 5 True False False False HDMI 5001 6 PROJECTOR 2 False False False False TV 6000 1 Network 4 False False False False TCP 1 True True True 7000 1 Room Selection - Output 7 False False False False VIDEO_SELECTION DiscreteCodes 0 0 False 19200 8 none 1 none 232 Control4 certified on 1/16/2017 for software released version: 2.9.0 JVC Projector Network and Serial Driver HARDWARE SETUP ============== Serial Control By Default the Projector should come with the control method set to serial. Menu/Functions/Communication Terminal Use a DB9 Cross (null modem) cable to connect to the controller. Baud rate : 19200bps Data length : 8 bits Parity : No Stop bit : 1 bit Flow control : No Connector : D-Sub 9pin Projector input : Control(RS-232C) Network Control The projector will come set to a static address. Set to DHCP or set this to a static address appropriate for your network. Turn on Control4 mode under network settings. Driver Notes and Limitations =========================== ISF MODE: You must turn the ISF Mode to ON before you can select the day or night modes. If the ISF is turned off and you have programming to change it to night mode the projector will ignore the command. Power On Delay Seconds: Used to establish the amount of time that will elapse during the power-on sequence before the driver continues to issue commands. Power Off Delay Seconds: Used to establish the amount of time that will elapse during the power-off and cool down sequence before the driver continues to issue commands. Power Off and Query Delay Seconds: Projectors have multiple power states like warm up and cool down. This timer is used to query the power status after the projector has booted up and cooled down. Then will allow the driver to send commands after it is fully on or fully off. PROGRAMMING =========== Variable: Projector_Operating_Status There are 4 states to this variable ON OFF COOLING EMERGENCY To access this variable go to programming and expand the device variables for the projector. Select the Projector_Operating_Status in the device events window (left). Do the same on the device action (right). In the Device Actions go to the conditionals of the Projector_Operating_Status variable. This is where you can type in the status of the variable. Example, you might want to trigger an email when the projector goes into its EMERGENCY state. Your script might say: When the variable (Room Name) ->Projector_Operating_Status changes If (Room Name) ->Projector->Projector_Operating_Status EQUALTO EMERGENCY Email Notification to 'dealer@bestdealer.com' with subject as : EMERGENCY Device Specific Commands: --Film --Cinema --Animation --Natural --HDR --Dynamic --THX --isf-Day --isf-Night --THX-Bright --THX-Dark --User1 --User2 --User3 --User4 --User5 Please note that not all commands are supported in each model. Check the user manual for your specific model. Version 101: -- Initial Release Picture Mode Set Picture Mode to PARAM1 NAME Mode LIST False Film Cinema Animation Natural HDR Dynamic THX isf-Day isf-Night THX-Bright THX-Dark User1 User2 User3 User4 User5 Color Profile Set Color Profile to PARAM1 NAME Mode LIST False Off Film1 Film2 Film3 Standard Cinema1 Cinema2 Anime1 Anime2 Video x.v.Color HDR BT.2020 THX Custom1 Custom2 Custom3 Custom4 Custom5 3D Cinema 3D Video 3D Animation 3D Film 3D THX Reference Color Temp Set Color Temp to PARAM1 NAME Mode LIST False 5500K 6500K 9300K High Bright Custom1 Custom2 HDR Xenon1 Xenon2 Xenon3 Gamma Table Set Gamma Table to PARAM1 NAME Mode LIST False Normal A B C Custom1 Custom2 Custom3 Hybrid Log Film1 Film2 ST.2084 Gamma Coorection Set Gamma Coorection to PARAM1 NAME Mode LIST False Normal A B C Import Import2 Import3 1 1.8 1.9 2 2.1 2.2 2.3 2.4 2.5 2.6 3 Film1 Film2 Hybrid Log ST.2084 Low Latency Set Low Latency Mode to PARAM1 NAME Mode LIST False Off On Graphic Mode Set Graphic Mode Mode to PARAM1 NAME Mode LIST False 2K 4K Anamorphic Set Anamorphic Mode to PARAM1 NAME Mode LIST False Off A B HDMI 2D 3D Set HDMI 2D/3D to PARAM1 NAME Mode LIST False 2D Auto Side by Side Top and Bottom 4K eshift Set 4K e-shift to PARAM1 NAME Mode LIST False Off On Source Set Source Mode to PARAM1 NAME Mode LIST False 480p 576p 720p50 720p60 1080i50 1080i60 1080p24 1080p50 1080p60 No Signal 720p 3D 1080i 3D 1080p 3D 4K(4096)60 4K(4096)50 4K(4096)30 4K(4096)25 4K(4096)24 4K(3840)60 4K(3840)50 4K(3840)30 4K(3840)25 4K(3840)24 Clear Motion Drive Set CMD Video Mode to PARAM1 NAME Mode LIST False CMD Off CMD Low CMD High CMD Inverse Telecine Aspect Set Aspect Ratio PARAM1 NAME Mode LIST False 4:3 16:9 Zoom Auto Just Full Trigger Set Trigger Mode to PARAM1 NAME Mode LIST False Trigger Off Trigger Power Trigger Anamorphic Lens Memory Select Lens Memory to PARAM1 NAME Mode LIST False Memory 1 Memory 2 Memory 3 Memory 4 Memory 5 Memory 6 Memory 7 Memory 8 Memory 9 Memory 10 Log Level LIST false 2 - Warning 0 - Alert 1 - Error 2 - Warning 3 - Info 4 - Debug 5 - Trace Log Mode LIST false Off Off Print Log Print and Log Command Delay Milliseconds RANGED_INTEGER false 250 200 2500 Power On Delay Seconds RANGED_INTEGER false 10 1 120 Power Off Delay Seconds RANGED_INTEGER 1 120 2 Power Status Query Delay Seconds RANGED_INTEGER 1 30 3 NetworkKeepAliveIntervalSeconds RANGED_INTEGER false 30 15 120 Connected To Network STRING true false JVCKENWOOD:Projector Control4 certified on 1/16/2017 for software released version: 2.9.0