Certified
Copyright 2016 Control4 Corporation. All rights reserved.
Control4
JVC KENWOOD
JVC KENWOOD DLA-X570R (SERIAL) (IP)
DLA-X570R
10/01/2015 3:00 PM
1/3/2017 3:30 PM
101
devices_sm\c4.gif
devices_lg\c4.gif
lua_gen
ip
DriverWorks
projector
True
False
2
0
0
0
1
6
Serial 232
1
True
False
False
True
RS_232
1000
1
HDMI 1
5
True
False
False
False
HDMI
1001
1
HDMI 2
5
True
False
False
False
HDMI
5001
6
PROJECTOR
2
False
False
False
False
TV
6000
1
Network
4
False
False
False
False
TCP
1
True
True
True
7000
1
Room Selection - Output
7
False
False
False
False
VIDEO_SELECTION
DiscreteCodes
0
0
False
19200 8 none 1 none 232
Control4 certified on 1/16/2017 for software released version: 2.9.0
JVC Projector
Network and Serial Driver
HARDWARE SETUP
==============
Serial Control
By Default the Projector should come with the control method set to serial. Menu/Functions/Communication Terminal
Use a DB9 Cross (null modem) cable to connect to the controller.
Baud rate : 19200bps
Data length : 8 bits
Parity : No
Stop bit : 1 bit
Flow control : No
Connector : D-Sub 9pin
Projector input : Control(RS-232C)
Network Control
The projector will come set to a static address. Set to DHCP or set this to a static address appropriate for your network.
Turn on Control4 mode under network settings.
Driver Notes and Limitations
===========================
ISF MODE: You must turn the ISF Mode to ON before you can select the day or night modes. If the ISF is turned off and you have programming to change it to night mode the projector will ignore the command.
Power On Delay Seconds:
Used to establish the amount of time that will elapse during the power-on sequence before the driver continues to issue commands.
Power Off Delay Seconds:
Used to establish the amount of time that will elapse during the power-off and cool down sequence before the driver continues to issue commands.
Power Off and Query Delay Seconds:
Projectors have multiple power states like warm up and cool down. This timer is used to query the power status after the projector has booted up and cooled down. Then will allow the driver to send commands after it is fully on or fully off.
PROGRAMMING
===========
Variable: Projector_Operating_Status
There are 4 states to this variable
ON
OFF
COOLING
EMERGENCY
To access this variable go to programming and expand the device variables for the projector. Select the Projector_Operating_Status in the device events window (left). Do the same on the device action (right). In the Device Actions go to the conditionals of the Projector_Operating_Status variable. This is where you can type in the status of the variable. Example, you might want to trigger an email when the projector goes into its EMERGENCY state. Your script might say:
When the variable (Room Name) ->Projector_Operating_Status changes
If (Room Name) ->Projector->Projector_Operating_Status EQUALTO EMERGENCY
Email Notification to 'dealer@bestdealer.com' with subject as : EMERGENCY
Device Specific Commands:
--Film
--Cinema
--Animation
--Natural
--HDR
--Dynamic
--THX
--isf-Day
--isf-Night
--THX-Bright
--THX-Dark
--User1
--User2
--User3
--User4
--User5
Please note that not all commands are supported in each model. Check the user manual for your specific model.
Version 101:
-- Initial Release
Picture Mode
Set Picture Mode to PARAM1 NAME
Mode
LIST
False
- Film
- Cinema
- Animation
- Natural
- HDR
- Dynamic
- THX
- isf-Day
- isf-Night
- THX-Bright
- THX-Dark
- User1
- User2
- User3
- User4
- User5
Color Profile
Set Color Profile to PARAM1 NAME
Mode
LIST
False
- Off
- Film1
- Film2
- Film3
- Standard
- Cinema1
- Cinema2
- Anime1
- Anime2
- Video
- x.v.Color
- HDR
- BT.2020
- THX
- Custom1
- Custom2
- Custom3
- Custom4
- Custom5
- 3D Cinema
- 3D Video
- 3D Animation
- 3D Film
- 3D THX
- Reference
Color Temp
Set Color Temp to PARAM1 NAME
Mode
LIST
False
- 5500K
- 6500K
- 9300K
- High Bright
- Custom1
- Custom2
- HDR
- Xenon1
- Xenon2
- Xenon3
Gamma Table
Set Gamma Table to PARAM1 NAME
Mode
LIST
False
- Normal
- A
- B
- C
- Custom1
- Custom2
- Custom3
- Hybrid Log
- Film1
- Film2
- ST.2084
Gamma Coorection
Set Gamma Coorection to PARAM1 NAME
Mode
LIST
False
- Normal
- A
- B
- C
- Import
- Import2
- Import3
- 1
- 1.8
- 1.9
- 2
- 2.1
- 2.2
- 2.3
- 2.4
- 2.5
- 2.6
- 3
- Film1
- Film2
- Hybrid Log
- ST.2084
Low Latency
Set Low Latency Mode to PARAM1 NAME
Mode
LIST
False
- Off
- On
Graphic Mode
Set Graphic Mode Mode to PARAM1 NAME
Mode
LIST
False
- 2K
- 4K
Anamorphic
Set Anamorphic Mode to PARAM1 NAME
Mode
LIST
False
- Off
- A
- B
HDMI 2D 3D
Set HDMI 2D/3D to PARAM1 NAME
Mode
LIST
False
- 2D
- Auto
- Side by Side
- Top and Bottom
4K eshift
Set 4K e-shift to PARAM1 NAME
Mode
LIST
False
- Off
- On
Source
Set Source Mode to PARAM1 NAME
Mode
LIST
False
- 480p
- 576p
- 720p50
- 720p60
- 1080i50
- 1080i60
- 1080p24
- 1080p50
- 1080p60
- No Signal
- 720p 3D
- 1080i 3D
- 1080p 3D
- 4K(4096)60
- 4K(4096)50
- 4K(4096)30
- 4K(4096)25
- 4K(4096)24
- 4K(3840)60
- 4K(3840)50
- 4K(3840)30
- 4K(3840)25
- 4K(3840)24
Clear Motion Drive
Set CMD Video Mode to PARAM1 NAME
Mode
LIST
False
- CMD Off
- CMD Low
- CMD High
- CMD Inverse Telecine
Aspect
Set Aspect Ratio PARAM1 NAME
Mode
LIST
False
- 4:3
- 16:9
- Zoom
- Auto
- Just
- Full
Trigger
Set Trigger Mode to PARAM1 NAME
Mode
LIST
False
- Trigger Off
- Trigger Power
- Trigger Anamorphic
Lens Memory
Select Lens Memory to PARAM1 NAME
Mode
LIST
False
- Memory 1
- Memory 2
- Memory 3
- Memory 4
- Memory 5
- Memory 6
- Memory 7
- Memory 8
- Memory 9
- Memory 10
Log Level
LIST
false
2 - Warning
- 0 - Alert
- 1 - Error
- 2 - Warning
- 3 - Info
- 4 - Debug
- 5 - Trace
Log Mode
LIST
false
Off
- Off
- Print
- Log
- Print and Log
Command Delay Milliseconds
RANGED_INTEGER
false
250
200
2500
Power On Delay Seconds
RANGED_INTEGER
false
10
1
120
Power Off Delay Seconds
RANGED_INTEGER
1
120
2
Power Status Query Delay Seconds
RANGED_INTEGER
1
30
3
NetworkKeepAliveIntervalSeconds
RANGED_INTEGER
false
30
15
120
Connected To Network
STRING
true
false
JVCKENWOOD:Projector
Control4 certified on 1/16/2017 for software released version: 2.9.0