Certified Copyright 2017 Control4 Corporation. All rights reserved. Control4 Sony Sony VPL-VW320ES VPL-VW320ES 11/14/2016 4:28 PM 6/2/2017 9:00 PM 103 devices_sm\c4.gif devices_lg\c4.gif lua_gen ip DriverWorks projector False False True False False False False False False False False False False False False False False 5001 6 PROJECTOR 2 False False False False TV 6001 6 Network Connection 4 true false false true TCP 53484 true true true HDMI 1 1 true true 5 1000 false false HDMI HDMI 2 1 true true 5 1001 false false HDMI 7000 1 Room Selection - Output 7 False False False False VIDEO_SELECTION 1 6 Serial 232 1 True False False True RS_232 DiscreteCodes 0 0 False 38400 8 even 1 none 232 Control4 certified on 6/8/2017 for software released version: 2.9.1 Sony Projector 2016-11-29 Contents --General notes and warnings --Control Method --Setup --Driver properties --Driver programming --Change log General notes and warnings The projector is provided with a network terminal. Using a Web browser, the status of the projector can be checked. To access the Web Utility, enter the following in the address bar of a Web browser: http:// (IP address of projector) When selecting the Setup Tab, you are prompted to enter a user name and password. Enter them as follows: ---User name: service ---Password: (model of projector) (lower-case) For Example: URL: http:// 192.168.1.189 User name: service Password: vpl-vw520es Control Method This driver supports Network and Serial control. When more than one control binding is made, the driver will automatically select the active control binding in this priority order: 1. Network 2. Serial Network control This device supports SDDP. For IP control using SDDP, this driver must be added to the project from the Discovered tab on the Items pane in Composer Pro. There is no need to set the hardware to a static address when using SDDP. Important Notes: 1. Sony projectors do not broadcast SDDP information in the OFF state. The projector must be ON to be discovered and identified by SDDP. Serial/RS-232 control 38400 baud / 8 data bits / 1 stop bits / even parity / no flow control Use a null modem cable to connect to your controller Setup Network Control: To set up the projector Press Menu on the remote go to ‘Setup Menu’ (Toolbox), scroll down to Remote Start and set this to ‘OFF’, scroll down to Network Management and set this to ‘ON’. Serial Control In Composer, bind the serial connection to a Control4 controller. The physical connection is a null modem cable. Driver properties Lamp Hours: Read only property listing the Lamp useage in hours as reported by the projector. Command Delay Milliseconds: The Command Delay Milliseconds value is simply the time elapsed between each command that is sent to the projector. Power On Delay Seconds: Used to establish the amount of time that will elapse during the power-on sequence before the driver continues to issue commands. Power Off Delay Seconds: Used to establish the amount of time that will elapse during the power-off sequence before the driver continues to issue commands. Power Status Query Delay Seconds: Used to establish the amount of time that will elapse after the power-on sequence before the driver issues a power status query command. Network Keep Alive Interval Seconds: When using the Network Control Method, the "Network Keep Alive Interval Seconds" value determines how often the driver will send a keep-alive query to the receiver. This query is useful in testing and maintaining a network connection. MAC Address: Read only property listing the projector's MAC address. IP Address: Read only property listing the projector's IP address. Connected to Network: Read only property indicating if the projector is online when using Network control. Driver Name: Read only property listing the driver's model name. Driver programming Project Variable and Events: VARIABLE NAME :: EVENT NAME [VARIABLE TYPE, (VALUES)] Lamp_Use_Time :: Lamp_Use_Time_Changed [NUMBER, (Running time of lamp by hours)] Error_Status :: Error_Status_Changed [STRING, (See list below.)] NO_ERROR LAMP_ERROR FAN_ERROR COVER_ERROR TEMP_ERROR D5V_ERROR POWER_ERROR TEMP_WARNING NVM_ERROR Error_Status2 :: Error_Status2_Changed [STRING, (See list below.)] NO_ERROR LENS_SHUTTER_ERROR HIGHLAND_WARNING Projector_Operating_Status :: Projector_Operating_Status_Changed [STRING, (See list below.)] STANDBY START UP START UP LAMP POWER ON COOLING1 COOLING2 SAVING COOLING1 SAVING COOLING2 Device Specific Commands: --Calib Preset (Parameters: Cinema Film 1, Cinema Film 2, REF, projector, Photo, Game, BRT CINE, BRT projector, User) --Color Temperature (Parameters: D93, D75, D65, D55, Custom1, Custom2, Custom3, Custom4, Custom5 --Lamp Control (Parameters: Low, High) --Contrast Enhancer (Parameters: Off, Low, Middle, High) --Advanced Iris (Parameters: Off, Full, Limited) --Film Mode (Parameters: Off, Auto) --Gamma Correction (Parameters: Off, 1.8, 2.0, 2.1, 2.2, 2.4, 2.6, Gamma7, Gamma8, Gamma9, Gamma10) --NR (Parameters: Off, Low, Middle, High, Auto) --Picture Muting (Parameters: On, Off) --Color Space (Parameters: BT.709, Color Space1, Color Space2, Color Space3, Custom) --Motionflow (Parameters: Off, Smooth High, Smooth Low, Impulse, Combination, True Cinema) --xvColor (Parameters: On, Off) --Reality Creation (Parameters: On, Off) --Color Correction (Parameters: On, Off) --Clear White (Parameters: Off, Low, High) --MPEG NR (Parameters: Off, Low, Middle, High, Auto) --Smooth Gradation (Parameters: Off, Low, Middle, High) --Reality Creation Database (Parameters: Mastered in 4K, Normal) --Picture Position (Parameters: 1.85:1, 2.35:1, Custom1, Custom2, Custom3) --Aspect (Parameters: Normal, V Stretch, 1.85:1 Zoom, 2.35:1 Zoom, Stretch, Squeeze) --Lens Shift (Parameters: Up, Down, Left, Right --Lens Focus (Parameters: Far, Near --Lens Zoom (Parameters: Large, Small) --Select 2D-3D Display (Parameters: Auto, 3D, 2D) --Select 3D Format (Parameters: Simulated 3D, Side-by-Side, Over-Under) --Select 3D Depth (Parameters: -2, -1, 0, 1, 2) --Select 3D Simulated Effect (Parameters: High, Middle, Low) --Select 3D Brightness (Parameters: High, Standard) --HDR (Parameters: Off, On, Auto) Change log Version 102: • Initial Release Version 103: • Fixed bug 30316: Programming on projector off triggers on poll of status. Log Level LIST false 2 - Warning 0 - Alert 1 - Error 2 - Warning 3 - Info 4 - Trace 5 - Debug Log Mode LIST false Off Off Print Log Print and Log Lamp Hours STRING true 0 Command Delay Milliseconds RANGED_INTEGER false 250 200 2500 Power On Delay Seconds RANGED_INTEGER false 10 1 120 Power Off Delay Seconds RANGED_INTEGER 1 120 2 Power Status Query Delay Seconds RANGED_INTEGER 1 30 3 NetworkKeepAliveIntervalSeconds RANGED_INTEGER false 5 5 25 MAC Address STRING true IP Address STRING true Connected To Network STRING true false Driver Name STRING VPL-VW320ES True Calib Preset Send Calib Preset PARAM1 to NAME Value LIST Cinema Film 1 Cinema Film 2 REF TV Photo Game BRT CINE BRT TV User Color Temperature Send Color Temperature PARAM1 to NAME Value LIST D93 D75 D65 Custom1 Custom2 Custom3 Custom4 Custom5 D55 Lamp Control Send Lamp Control PARAM1 to NAME Value LIST Low High Contrast Enhancer Send Contrast Enhancer PARAM1 to NAME Value LIST Off Low Middle High Advanced Iris Send Advanced Iris PARAM1 to NAME Value LIST Off Full Limited Film Mode Send Film Mode PARAM1 to NAME Value LIST Off Auto Gamma Correction Send Gamma Correction PARAM1 to NAME Value LIST Off 1.8 2.0 2.1 2.2 2.4 2.6 Gamma7 Gamma8 Gamma9 Gamma10 NR Send NR PARAM1 to NAME Value LIST Off Low Middle High Auto Picture Muting Send Picture Muting PARAM1 to NAME Value LIST On Off Color Space Send Color Space PARAM1 to NAME Value LIST BT.709 Color Space1 Color Space2 Color Space3 Custom Motionflow Send Motionflow PARAM1 to NAME Value LIST Off Smooth High Smooth Low Impulse Combination True Cinema xvColor Send xvColor PARAM1 to NAME Value LIST On Off Reality Creation Send Reality Creation PARAM1 to NAME Value LIST Off On Color Correction Send Color Correction PARAM1 to NAME Value LIST On Off Clear White Send Clear White PARAM1 to NAME Value LIST Off Low High MPEG NR Send MPEG NR PARAM1 to NAME Value LIST Off Low Middle High Auto Smooth Gradation Send Smooth Gradation PARAM1 to NAME Value LIST Off Low Middle High Reality Creation Database Send Reality Creation Database PARAM1 to NAME Value LIST Mastered in 4K Normal Picture Position Send Picture Position PARAM1 to NAME Value LIST 1.85:1 2.35:1 Custom1 Custom2 Custom3 Aspect Send Aspect PARAM1 to NAME Value LIST Normal V Stretch 1.85:1 Zoom 2.35:1 Zoom Stretch Squeeze Lens Shift Send Lens Shift PARAM1 to NAME Value LIST Up Down Left Right Lens Focus Send Lens Focus PARAM1 to NAME Value LIST Far Near Lens Zoom Send Lens Zoom PARAM1 to NAME Value LIST Large Small Select 2D 3D Display Select 2D 3D Display PARAM1 for NAME Value LIST Auto 3D 2D Select 3D Format Select 3D Format PARAM1 for NAME Value LIST Simulated 3D Side-by-Side Over-Under Select 3D Depth Select 3D Depth PARAM1 for NAME Value LIST -2 -1 0 1 2 Select 3D Simulated Effect Select 3D Simulated Effect PARAM1 for NAME Value LIST High Middle Low Select 3D Brightness Select 3D Brightness PARAM1 for NAME Value LIST High Standard HDR Send HDR PARAM1 to NAME Value LIST Off On Auto Audio/Video Sony:Projector:VPL-VW320ES Control4 certified on 6/8/2017 for software released version: 2.9.1